Make an Appointment

Edit Template
Daulatabad, Gurugram|ISO Certified
T-Bush
Flanged Bush • Compression Limiter • Cold Forged

T-Bush
& Flanged
Bush

Sleeve with flange at one end — shaped like letter T when cut in half. Sits in hole, bolt passes through, carries clamping load so whatever surrounds it doesn't have to.

Bore 6-16mmFlange 14-35mmLength 5-40mmSAE 1008/1010One-piece forged

FASTENER TECH cold forges T-bushes for auto & industrial assemblies — almost always to customer's own drawing. Gurugram.

T-Shape Logic

Steel Against Steel —
Soft Part Not Crushed
Bore6 - 16 mm
Sleeve OD9 - 22 mm
Flange Dia14 - 35 mm
Length5 - 40 mm
MaterialLow Carbon Steel
FinishZn / Phos / Plain
Flange stops bush being pushed through hole + spreads load. Length sets clamp height.

Ready Stock • Custom Drawing Our T-Bush & Flanged Bush Range

MS / EN8 / Nylon T-bushes for hinge, pivot & insulation — 150+ MT monthly cold forging capacity. Click image to zoom.

Most Demanded
T-Bush

Type TB-01 Small T-Bush

For door hinge & automotive pivot — tight tolerance

MS / EN8OD 10-20mmZinc
Nylon / MS
T-Bush Nylon

Type TB-02 Insulation T-Bush

Nylon / Fibre for electrical insulation & anti-rattle

Nylon 66Flange 15-30mmCustom
Flanged
Flanged Bush

Type FB-01 Flanged Bush

Heavy duty for suspension & linkages — press fit

EN8 / EN36OD 20-50mmBlack / Zinc
Custom
Long T-Bush

Type TB-03 Long T-Bush

Extended length for deep housing — drawing based

MS / SS304Length 15-80mmCold Forged
What A T-Bush Does

Rubber Tighten Karo Toh Gives Way — Bush Changes Game

Tighten bolt through rubber, plastic or thin sheet — material gives way. Joint loosens, part deforms. Put steel bush in hole — bolt now clamps steel against steel through bush, softer material held without being crushed.

Flange stops bush being pushed through hole, spreads load wider. That's the “T”.

Features

One-Piece Forged — No Welded Flange

✓ One-piece cold forged — no welded flange
✓ Grain flow follows flange radius
✓ Pierced bore concentric with OD
✓ Flat, square flange face
✓ Close control over length
✓ Smooth surface straight from die
Parameter
Typical Range
Bore diameter
6 mm to 16 mm
Sleeve OD
9 mm to 22 mm
Flange dia
14 mm to 35 mm
Overall length
5 mm to 40 mm
Material
SAE 1008, 1010, 1018
Finish
Zinc plated, phosphated or plain

Where Used

Rubber engine & gearbox mountingsSuspension linksStabiliser bar mountsSeat frames & trackPlastic housings & coversAir intakeRadiator mountsExhaust hangers

Industries Served

Passenger & CV2W / 3WRubber & anti-vibrationSeating systemsPlastic moulding

Why Forge Instead Of Machining?

Many T-bushes still turned from bar/tube. Works but wasteful. Turning flanged bush from solid removes entire bore & most material around sleeve.

Cold forging forms flange & extrudes sleeve from small slug, then pierces bore. Nearly all steel ends in part. Flange stronger — grain turns corner.

Design Tips

Leave Radius Under Flange

Sharp corner = stress raiser + shortens tool life.

Set Length Right

Slightly below free thickness if want pre-compression.

Think Corrosion

Plated bush pressed into rubber mount will be there for life of vehicle.

FAQ — Buyers Ask

T-Bush — Common Questions

Almost always custom — send drawing, we check feasibility in 24hr.

📦Bulk Stock ReadyMS / EN8 / Nylon
✓One-Piece ForgedNo welded flange
⚡24Hr FeasibilityDrawing to price
🌍Gurugram PlantDaulatabad Ind. Area
Same as flanged / top hat bush?

Yes — different names for same basic T-shape.

What is compression limiter?

Bush placed in plastic/rubber to take bolt load & prevent creeping/cracking.

Stepped bore / two diameters?

In most cases yes — send drawing we'll check.

Convert machined bush to forged?

Often we can — review & tell saving.

Get A Quote — Fast Response

Get A Quote For T-Bush & Flanged Bush

Share ID x OD x Flange dia x Length, material, finish & monthly qty. We'll study & reply with feasibility & price.

💬 WhatsApp
Dashwood contempt on mr unlocked resolved provided of of. Stanhill wondered it it welcomed oh. Hundred no prudent he however smiling at an offence.

Quick Links

About

Help Centre

Business

Contact

About Us

Terms of Use

Our Team

How It Works

Accessibility

Support

FAQs

Terms & Conditions

Privacy Policy

Career

Company Info